ProFlow Water softener Service Manual

© 2014 erie water treatment TM-EN-ProFlow-Rev2014.05 Technical Manual WATER SOFTENER

ELECTRONIC CONTROL PANEL Page 10 Picture 13 symbol button function  SCROLL to advance to the next parameter  UP to increase the value of the

ELECTRONIC CONTROL PANEL Page 11 MANUAL REGENERATION It is possible to manually initiate a regeneration. 1. Press the scroll  button repeated

ELECTRONIC CONTROL PANEL Page 12 PROGRAMMING INSTRUCTIONS – PARAMETER SET LEVEL  Before entering the programming mode, make sure that the cont

ELECTRONIC CONTROL PANEL Page 13 SIMPLEX ECO: 1. Press the scroll  button and hold it for 5 sec until the display shows: 2. Within 10 sec,

ELECTRONIC CONTROL PANEL Page 14 DUPLEX ECO ALTERNATING:  The 2 Simplex systems, that make up a Duplex system, must be programmed individually

ELECTRONIC CONTROL PANEL Page 15 DUPLEX/TRIPLEX ECO PARALLEL:  The 2/3 Simplex systems, that make up a Duplex/Triplex system, must be progr

ELECTRONIC CONTROL PANEL Page 16 DIAGNOSTICS LEVEL Besides of all programming parameters, a series of operating parameters can be consulted

MAINTENANCE Page 17 ROUTINE CHECKS Regularly the user should perform a basic check to verify if the water softener is functioning correctly, on

HYDRAULIC FLOW DIAGRAMS Page 18 SERVICE BACKWASH BRINE DRAW / SLOW RINSE FAST RINSE / REFILL

Page 19

TABLE OF CONTENT & INSTALLATION RECORD Page 2 Table of content & Installation record ...

TROUBLESHOOTING Page 20 PROBLEM CAUSE SOLUTION Hard (untreated) water to service Open or defective bypass Close or replace bypass Simplex only

TROUBLESHOOTING Page 21 PROBLEM CAUSE SOLUTION Control valve fails to refill brine tank Improper refill time setting Verify that refill time

ELECTRICAL WIRING DIAGRAMS Page 22 SIMPLEX TEMPO  = position switches = power lead  = drive motor  = auxilliary contact (24V, max. 500

ELECTRICAL WIRING DIAGRAMS Page 23 DUPLEX ECO - ALTERNATING  = position switches = flow meter  = power lead  = drive motor  = service

DEFAULT PARAMETER SETTINGS Page 24 (1) When the Hardness unit is changed, the Exchange capacity per liter resin needs to be adjusted accordingl

COMPOSITION OVERVIEW Page 25 Model Resin volume PN Control valve, incl. EuroT transformer, 1” male BSP connections InterConnect cable Service V

EXPLODED VIEW - SIMPLEX TEMPO/ECO Page 26

EXPLODED VIEW - SIMPLEX TEMPO/ECO Page 27 (*) Recommended Spare Part Item PN Description Remark (*) 1 PT/1035/BA Pressure tank 10x35 2

EXPLODED VIEW - DUPLEX ECO ALTERNATING Page 28

EXPLODED VIEW - DUPLEX ECO ALTERNATING Page 29 (*) Recommended Spare Part Item PN Description Remark (*) 1 PT/1035/BA Pressure tank 10x

WARNING & SAFETY INSTRUCTIONS Page 3  Before you begin the installation of the water softener, we advise you read and carefully follow the

EXPLODED VIEW - DUPLEX ECO PARALLEL Page 30

EXPLODED VIEW - DUPLEX ECO PARALLEL Page 31 (*) Recommended Spare Part Item PN Description Remark (*) 1 PT/1035/BA Pressure tank 10x35

EXPLODED VIEW - TRIPLEX ECO PARALLEL Page 32

EXPLODED VIEW - TRIPLEX ECO PARALLEL Page 33 (*) Recommended Spare Part Item PN Description Remark (*) 1 PT/1035/BA Pressure tank 10x35

EXPLODED VIEW - TIMER HEAD - SIMPLEX Page 34

EXPLODED VIEW - TIMER HEAD - SIMPLEX Page 35 (*) Recommended Spare Part Item PN Description Remark (*) 1 70971 Power lead with plug

EXPLODED VIEW - TIMER HEAD - DUPLEX ALTERNATING Page 36

EXPLODED VIEW - TIMER HEAD - DUPLEX ALTERNATING Page 37 (*) Recommended Spare Part Item PN Description Remark (*) 1 70971 Power lead w

EXPLODED VIEW - TIMER HEAD - DUPLEX/TRIPLEX PARALLEL Page 38

EXPLODED VIEW - TIMER HEAD - DUPLEX/TRIPLEX PARALLEL Page 39 (*) Recommended Spare Part Item PN Description Remark (*) 1 70971 Power le

OPERATING CONDITIONS & REQUIREMENTS Page 4  OPERATING PRESSURE: min. 1,4 / max. 8,3 bar  this system is configured to perform optimally a

EXPLODED VIEW - VALVE BODY Page 40

EXPLODED VIEW - VALVE BODY Page 41 (*) Recommended Spare PartItem PN Description Remark (*) 1 21/83 Drain connection  2 568/271/J B

TECHNICAL DATA Page 42 Technical specifications: (1) Supplied with 230/24V-50Hz transformer. Performances @ 3 bar operating pressure and bri

TECHNICAL DATA Page 43 Model Triplex Parallel Resin 3 x 25 3 x 50 3 x 75 3 x 100 3 x 125 3 x 150 Brine tank volume (ltr) 3 x 125 3 x 1

AQUION, INC. Lammerdries-Oost 30c B-2250 Olen Belgium  +32 (0) 14-28.51.71  +32 (0) 14-28.51.70 RPR/RPM Turnhout BWT/TVA/VAT B

© 2013 Aquion, Inc. PP-ProFlow-Rev2014.01 r 1 2.a 2.b 3.a 3.b

© 2013 Aquion, Inc. PP-ProFlow-Rev2014.01 r 4.a 4.b r 5.a 5.b

© 2013 Aquion, Inc. PP-ProFlow-Rev2014.01 6 7.a 7.b r 8.a 8.b

© 2013 Aquion, Inc. PP-ProFlow-Rev2014.01 r 9 10 r 11 r 12

© 2013 Aquion, Inc. PP-ProFlow-Rev2014.01 13 14.a 14.b 14.c

ASSEMBLY Page 5 CONTENT CHECK  Actual parts that you have received, may differ from the pictures/illustrations in these Instructions!  For

© 2013 Aquion, Inc. PP-ProFlow-Rev2014.01 15

© 2013 Aquion, Inc. PP-ProFlow-Rev2014.01

© 2013 Aquion, Inc. PP-ProFlow-Rev2014.01

ASSEMBLY Page 6 BRINE TANK Picture 1 11. Move the brine tank to the correct installation location; position it on a flat and level surface. Ma

INSTALLATION Page 7 INLET & OUTLET  Check the water pressure at the place of installation of the water softener; it should never exceed 8,

INSTALLATION Page 8 DRAIN  We recommend the use of a stand pipe with air trap.  To prevent backflow from the sewerage system into the wate

START-UP Page 9 PRESSURIZING 1. Put the bypass system in 'bypass' position. 2. Make sure the electronic controller(s) of the