Models: SA-Eliminator 48 S-100 SA-Eliminator 70 S-100 SA-Eliminator 90 S-100Installation, Opeeration, and Maintenance ManualS-100
| 10 | ProFlow EliminatorRemoving the Valve Assembly for Servicing1. Unplug the power cord.2. Shut off water supply or put bypass valve(s) into
ProFlow Eliminator | 11 | Preventive MaintenanceInjector Screen and InjectorInspect and clean brine tank and screen fi lter on end of brine pick
| 12 | ProFlow EliminatorSpecifications: Control Valve AUV - 268-460iHydrostatic Test Pressure. . . . . . . . . . . . . . . . . . . . . . . . .
ProFlow Eliminator | 13 | 0.200.150.100.050.001.000.750.500.250.0020 40 60 80 100 120400 600 800 1000 1200 1400 1600 1800Brine DrawRinseT
| 14 | ProFlow EliminatorBrine Valve (1) Inlet Valve (3) Bypass Valve (2) Outlet Valve (4) Refill Valve (5) Rinse Drain Valve (6) Backwash Drain
ProFlow Eliminator | 15 | Brining / Slow-Rinse PositionValve Position1 Closed2 Closed3 Open4 Open5 Open6 Closed7 ClosedPurge PositionValve Posi
| 16 | ProFlow Eliminator121486319Replacement Parts AUV - 1053832ProFlow: High-Flow Eliminator SeriesParts ListCode Part # Description Qty1AUV-1
ProFlow Eliminator | 17 | Replacement Parts: Distributor AssemblyAll Models (48, 70, and 90)DST-2001: High-Flow Upper Distributor214,5736159141
| 18 | ProFlow EliminatorCode #2460i ControlBYPASSBYPASSCode #3: BypassBP-A-1040930Code Part # Description Qty2460i Control 13AVP-1040930 1265 B
ProFlow Eliminator | 19 | TroubleshootingThe technology upon which the control valve is based is well established and proven in service over m
R&M Water Group28 South 1550 WestLindon, Utah 84042P: (801) 785-5557F: (801) 785-7823© 2004 R&M Water Group All rights reserved.ProFlow Elim
| 20 | ProFlow Eliminator460i Control TroubleshootingProblem Possible Cause SolutionClock does not display time of day. Transformer cord unplugg
ProFlow Eliminator | 21 | 460i Control Troubleshooting (con't)Problem Possible Cause SolutionControl will not regenerate automatically or
| 22 | ProFlow EliminatorDisinfection of Water ConditionersThe materials of construction of the modern water conditioner will not support bacter
Manufacturer’s WarrantyR&M Water GroupA Division of Water Technologies Inc.To the original purchaser, the valve body, mineral container, cation re
R&M Water Group28 South 1550 WestLindon, Utah 84042 P: (801) 785-5557 F: (801) 785-7823© 2004 R&M Water Group All rights reserved.ProFlow Elim
ProFlow Eliminator | 3 | Table of ContentsInstallation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
| 4 | ProFlow EliminatorInstallationAll plumbing and electrical connections must conform to local codes.Inspect unit carefully for carrier short
ProFlow Eliminator | 5 | Right Way1” Air GapBrine Line ConnectionIt will be necessary to install the brine line to the brine fi ing on the val
| 6 | ProFlow EliminatorPlacing Conditioner into OperationA er all previous steps have been completed, the unit is ready to be placed into oper
ProFlow Eliminator | 7 | Pro Flow 460i Series Control SettingsProFlow 460i ControlProgrammingPlug the wall-mount transformer into a functioning
| 8 | ProFlow EliminatorHardness SettingMove the jumper to the set of pins next to the word HARDNESS (8). Press the black TIME SET bu on until
ProFlow Eliminator | 9 | The amount of salt placed in the brine tank has nothing to do with the amount of salt used during the regeneration cyc
Comments to this Manuals